Howen Configuratio Procedure Via Mobile app ( Howen iTool new firmware)

Howen Configuratio Procedure Via Mobile app ( Howen iTool new firmware)

A. Quick setup.

 The Howen iTool application is used to configure the device in this guide.

To point the device to your whitelabel platform, follow the steps below:

1. Download the Howen iTool here


2. Connect the dash camera to your mobile phone's Wi-Fi or device Hotspot.

     The device is available for connection only 3 minutes after it is switched on.

3. Open the Howen iTool application and find the device.

Use the refresh button if necessary.





4. Select and log in to the device. The default password is 111111.






 

B. Configure System Settings.

To configure the device, click on config. 


Set user details if interested in device security 




To set your time zone, go to the clock and then set your time zone.  Remember, when adding the device on the platform, you will be required to apply an offset 



To set power-related settings.



To set  sleep-related settings

To set disk settings



Set your preferred audio settings



Here you can manage your parameters /configuration items





C. Configure Video Settings.


To set the very key general settings.





Configure the Mstream  video settings 



Set  the stream video settings 



Under the storage device, the file storage-related settings 



If you have an On-Screen Display (OSD) set the parameters 




video blocking and privacy settings as per your preference




D. Configure Network Settings 

i. Pointing gps and video data to the server to receive GPS location data.


Update the server settings   on centre-1, make sure you select H-protocol

server is: data.gpsiot.net port 8933

for ftp server details, 

server: media.gpsiot.net

user and password: Reach out to support







ii. Set the ftp server details (server to receive  video files)



iii. Set apn settings 







iv. Set the Wi-Fi settings. This will enable device report using wiffi connectivity when in range





E. Configure Alarm Settings.

Configuration of Alarms/event select Alarm



To set speed-related events, go to alarm >>speed



To set harsh related  events, go to alarm>> G sensor

impact./crash incident


harsh cornering/tilt incident



Harsh acceleration incident





Harsh braking 





motion detection /motion events 





set voltage-related events 



F. General overview


. Click on SYSTEM>>Status  to get a general overview

































If you need to change the ID, select the Terminal item of the System section in the settings. Change the ID in the Dev ID field and click Save.
                       

6. In the settings, select the Center item of the Network section.

7. Update the server settings   on center-1   make sure you select H-protocol

server is: data.gpsiot.net port 8933
for ftp server details, contact 
server is : media.gpsiot.ner

user and password: Reach out to support 

Specify the server IP and port c. Click Save.
                                   

8. Update Apn settings
In the settings, select the Dial item of the Network section.
                                







    • Related Articles

    • Howen Configuratio Procedure Via Web

      To access this page via the web. Ensure the camera is connected to the same wiff as your pc. Connect to the camera hotspot and read the camera IP.. Use the IP on your browser. You will land on the page below .. The first option is to configure the ...

    • Video Monitoring

      Video telematics It refers to the integration of video technology with telematics systems to monitor vehicles and drivers. It combines video footage with data collected from telematics devices, such as GPS, speed sensors, accelerometers, and other ...

    • Howen dashcam/mult channel video device

      You can connect to the device hotspot then configure the device according to your preference. Ensure the device is set to H protocol and the following settings Gps data server ::: Server : data.gpsiot.net port : 8933 Media server details ::: Ftp ...

    • PWA Mobile app

      The PWA version is 1 of 3 available mobile app options for monitoring the location of your assets: GPS MonitorPlus - free, generic brand, instantly available, on Google Android or Apple iOS Own branded GPS MonitorPlus on both stores (Additional cost, ...

    • Teltonika DualCam Configuration (FMC650)

      FMC650 DualCam Configuration (!) Required firmware version - 03.00.14.Rev.114. Firmware errata. Firmware download for FMX125/FMX225/FMC650 Link: Firmware Password: 3RpOAf96 It is necessary to change Data Protocol to Codec 8 Extended In RS232 \ RS485 ...